Hi, this is Wayne again with a topic “Avoiding Common PC Building Traps – Episode 2”.
So in our last episode of this now two-part series, we tackled a handful of common problems that new computer builders face and even some things that those of you with experience would do well to remember. You can check that out right there, but obviously there was no way we were going to be able to cover everything that could go wrong in just one five-minute video. So what are some other things that you should be looking out for? Let’S start small and talk about those annoying little front panel connectors, unlike most of the connections inside your PC, the front panel header isn’t keyed in any way, so it’s possible to plug things in in the wrong orientation and considering how many pins there are on the Header, it can be one of the most frustrating parts of any build to make this as painless as possible. Look at the diagram on your motherboard near the front panel header or in your motherboard manual, you’ll, usually see, plus and minus signs to indicate which way to plug in your leads. But sometimes this isn’t clearly indicated on the leads themselves very frustrating.
If this is the case, the colored wire is usually positive and failing that you can look for a little tiny, embossed arrow, which indicates the positive side, but you shouldn’t worry about it too much anyway. If you plug something in backwards and it doesn’t work, you won’t damage anything just turn it around and try again and the orientation for the pins for your power and reset switches doesn’t matter anyway, since all those do is complete a circuit by shorting the pins. When you press the button, but now let’s go from talking about small stuff to something big, namely that tower style, CPU air cooler, that’s beefier than a porterhouse steak. If you’re going with one of these pay close attention to your K, specs a lot of people assume that if your CPU socket is listed on the box as one that fits, the cooler will sit. But we how bulky some higher-end coolers are and the fact that even standard ATX cases aren’t a uniform width. You could end up not being able to fit ram into your slots or your side panel on. If you aren’t careful. Fortunately, memory manufacturers list the height of their modules and many case manufacturers give a max cooler clearance, spec that takes into account the height of the motherboard itself.
So have a look at that, if you don’t plan to use a water cooler and speaking of huge CPU coolers, you probably have one because you’re trying to overclock your processor right and if it’s an Intel well you’ve made sure to buy an unlocked, K or X Series right, you should be ready to go not so fast aside from meeting an unlocked processor, your motherboard chipset also needs to support overclocking. An easy way to make sure it does before you buy is just to look at the letter in the chipset name. If it contains a Zed or an X, such as Z, 270 or X 99, then you’re all set to overclock. But if it’s something else like an H B or Q, you’ll probably find that unless your motherboard manufacturer has an experimental bios available, which is quite uncommon, you can’t change your CPU multiplier.
Ouch. Ok then, so you’ve got the right, motherboard cooler in case and you’re ready to put it all together, but wait. There are two things you really do not want to forget. The first is the i/o shield at the back of the case, which I would strongly recommend putting in before doing anything else.
Countless builders, even very experienced ones, have installed all their components without realizing until they were nearly done that they forgot the i/o shield, forcing them to take everything out and put it all back in unless they want to live with an awkward, gaping hole in their case Or even worse, they might have missed one of the little tabs that you have to bend up, sometimes ending up with it stuck in a port shorting it out and killing it. The second one not to forget is when it is time to install that CPU cooler. Don’T forget to peel the protective film off the bottom of the heatsink, since you don’t actually look at that part of the heatsink, the part that actually contacts the CPU very often it’s easy to mount the cooler without removing this plastic. If you do that, not only will you experience abnormally high CPU temperatures, but the plastic can melt, leaving an ugly mess for you to deal with later, as well as wasted thermal compound and time speaking of avoiding messes.
What are some of your top tips for preventing issues with your shiny new build? Let us know in the comments, and you might see your ideas in a future tech, quickie episode. Also, let us know if you’d like to see more, avoiding PC building traps. Videos just like this one, but if you were thinking to yourself gee, I just avoided all these PC building traps and I’ve got this great PC, but I can’t get on frickin websites because their country blocked, then I have a solution for you. Title bear it’s easy to use and lets you tunnel, your internet connection to one of 20 different countries, whether you’re using iOS, Android, PC Mac. They also have a Chrome extension. They make it as simple as just picking a country pressing a button and boom without any of the rigmarole that goes along with other VPN solutions.
Your connection gets encrypted with AES 256-bit encryption and your public IP address gets switched. It’S so easy to use. They have a top rated privacy policy and you can try it out for free over at Tunnel, Bear comm slash Linus with 500 Meg’s of data thrown in for nothing and no credit card required.
Then, if you decide to try out an unlimited plan, you can save 10 % by using that link below thanks for watching guys like or dislike, leave a comment. If you have a suggestion for a future video check out our other channels and don’t forget to subscribe subscribe, it’s important, you might even get a notification in your subscription box if you’re lucky .